链路聚合有成端口聚合,断口捆绑,英文名port trunking.功能是将交换机的多个低带宽端口捆绑成一条高带宽链路,可以实现链路负载平衡。避免链路出现拥塞现象。通过配置,可通过两个三个或是四个端口进行捆绑,分别负责特定端口的数据转发,防止单条链路转发速率过低而出现丢包的现象。
Trunking的优点:价格便宜,性能接近千兆以太网;不需要重新布线,也无需考虑千兆网传输距离极限问题;trunking可以捆绑任何相关的端口,也可以随时取消设置,这样提供了很高的灵活性还可以提供负载均衡能力以及系统容错。
命令:port-group mode {active|passive|on}
no port-group
功能:将物理端口加入Port Channel,该命令的no 操作为将端口从Port Channel 中去除
参数: 为Port Channel 的组号,范围为1~16;active(0) 启动端口的LACP 协议,并设置为Active 模式;passive(1) 启动端口的LACP 协议,并且设置为Passive 模式;on(2) 强制端口加入Port Channel,不启动LACP 协议。
举例:在Ethernet0/0/1 端口模式下,将本端口以active 模式加入port-group
Switch(Config-Ethernet0/0/1)#port-group 1 mode active
命令:interface port-channel
功能:进入汇聚接口配置模式
命令模式:全局配置模式
举例:进入port-channel1 配置模式
Switch(Config)#interface port-channel 1
Switch(Config-If-Port-Channel1)# |
举例1:如果交换机Switch1 上的1,2,3 端口都是access 口,并且都属于vlan 1,将这三个端口以active 方式加入group 1,Switch2 上6,8,9 端口为trunk 口,并且是allow all,将这三个端口以passive 方式加入group 2,将以上对应端口分别用网线相连。
方法1配置步骤如下:
Switch1#config
Switch1 (Config)#interface eth 0/0/1-3
Switch1 (Config-Port-Range)#port-group 1 mode active
Switch1 (Config-Port-Range)#exit
Switch1 (Config)#interface port-channel 1
Switch1 (Config-If-Port-Channel1)#
Switch2#config
Switch2 (Config)#port-group 2
Switch2 (Config)#interface eth 0/0/6
Switch2 (Config-Ethernet0/0/6)#port-group 2 mode passive
Switch2 (Config-Ethernet0/0/6)#exit
Switch2 (Config)# interface eth 0/0/8-9
Switch2 (Config-Port-Range)#port-group 2 mode passive
Switch2 (Config-Port-Range)#exit
Switch2 (Config)#interface port-channel 2
Switch2 (Config-If-Port-Channel2)# |
配置结果:
过一段时间后,shell 提示端口汇聚成功,此时Switch1 的端口1,2,3 汇聚成一个汇聚端口,汇聚端口名为Port-Channel1,Switch2 的端口6,8,9 汇聚成一个汇聚端口,汇聚端口名为Port-Channel2,并且都可以进入汇聚接口配置模式进行配置。
相关文章
思科网络TCP_IP连接故障处理
路由器设置V 应用[I ec篇]
中小企业网络选择 LV 是否适合
交换机链路聚合在网络中的作用
技巧:子网掩码的快速计算方法
新手必知:CiscoIOS软件基础
最新思科考试中心以及VUE的考场安排
澳大利亚华人论坛
考好网
日本华人论坛
华人移民留学论坛
英国华人论坛