CCNA考题分析配置RIP路由协议Cisco认证考试

文章作者 100test 发表时间 2009:04:09 22:49:12
来源 100Test.Com百考试题网


问题:

you are a cisco certified expert.you have been contracted by the testcenter pro chain to fix a problem that was caused by a mcp certified technicician who could net complete the configuration of the routers.

this testcenter pro chain has three stores and wanted to maintain their bicycle repair business in a centralized manner through network connectivity.they then asked the local mcp certitified technician to configure the routers,but the technician failed to establish connectivity among the routers.

the routers are named router1,router2,and router3,respectively.

identify the fault and make the appropriate change(s) to rectify the configuration fo the routers.the mcp technician configured the routers with the specification that follows:

·the routers are named router1,router2,router3
·rip is the routing protocol
·clocking is provided on the serial 0 interfaces
·the password on each router is pconline
·the subnet mask on all interfaces is the default mask.
·the ip addresses are listed in chart below.

router1:

e0 192.168.27.1
e1 192.168.29.1
s0 192.168.31.1
secret password:pcjob

router2:

e0 192.168.35.1
s0 192.168.33.1
s1 192.168.31.2
secret password:pcjob

router3:

e0 192.168.37.1
s1 192.168.33.2
secret password:pcjob

to configure the router you need to click on the host icon that is connected to the router by a serial cable.

有一名mcp配置的路由器无法连通,请你去帮忙给解决,情况如下:

·路由器被命名为router1,router2,router3
·使用rip协议
·serial 0时钟设置
·每个路由器的密码都是“pcjob”
·所有接口的子网掩码均为默认掩码


解答:

命令后面的注释只在第一次出现时进行提示讲解。

路由器1在主机2上配置:

router1>.en --------enable命令的简写,进入到用户配置模式,只有在用户配置模式才可以以对路由器进行相关的配置操作,考试中最好是将命令写全
password:pcjob --------输入密码:pcjob,正式使用中的密码在输入时是不可见的
router1#conf t --------config terminal命令的简写,进入终端配置模式
router1(config)#int e0 --------interface ethernet 0命令的简写,进入e0端口进行配置
router1(config-if)#ip add 192.168.27.1 255.255.255.0 --------ip address命令简写,注意它后面的ip 地址一定要跟随子网掩码
router1(config-if)#no shut --------启用端口,no shutdown命令简写
router1(config-if)#exi --------退出端口配置模式
router1(config)#int e1



相关文章


关于Cisco路由协议题和答案(中文)Cisco认证考试
CCNA考题分析OSI参考模型Cisco认证考试
CCNA考题分析交换机转发时延原因简析Cisco认证考试
CCNA考题分析OSPF协议Cisco认证考试
CCNA考题分析配置RIP路由协议Cisco认证考试
华为GB0360考试试题Cisco认证考试
华为GB0320认证考题Cisco认证考试
华为GB0180考试试题Cisco认证考试
华为GB0280认证考题Cisco认证考试
澳大利亚华人论坛
考好网
日本华人论坛
华人移民留学论坛
英国华人论坛